🔧 Handyperson

QUICK ANSWER: Turn off cooler, access filter/cooling pads (usually top or side access), slide out old pad, measure and cut new pad to fit, install new pad with water flow direction noted. Annual pad replacement (March–April) ensures cool efficiency all summer. Budget 30-45 minutes, $30-80 for pads.

What You’ll Need

  • Replacement evaporative cooling pads—correct size/type for your cooler (check manual; Bunnings, Mitre 10, climate control shops)
  • Utility knife or scissors (cutting pads to fit)
  • Measuring tape
  • Work gloves (cooling pads can have rough edges)
  • Hose or bucket (flushing old pad if blocked)
  • Spirit level (checking cooler alignment)
  • Step ladder (if cooler is roof-mounted or high)

About This Problem in Melbourne

Melbourne summer heat can exceed 40°C. Evaporative coolers (also called swamp coolers) cool by up to 15°C efficiently and cheaply—critical for comfort and energy bills. Cooling pads become clogged with dust, scale, and mineral deposits over a season. Annual replacement (March–April) before peak summer demand ensures maximum cooling efficiency and extends cooler unit life.

Step-by-Step

  1. Step 1: Turn off the cooler

    2. Switch off at the wall or circuit breaker. Allow fan/motor to stop completely before access.

[IMAGE_PLACEHOLDER: cooler-power-off]

  1. Step 2: Locate the cooling pads

    2. Most pads are accessed from the top (roof units) or sides (window units). Check manual for access points.

[IMAGE_PLACEHOLDER: pad-location-identification]

  1. Step 3: Remove access panel or grille

    2. Unclip or unscrew access panel. Some coolers have magnetic covers—just slide off.

[IMAGE_PLACEHOLDER: access-panel-removal]

  1. Step 4: Inspect old cooling pad

    2. Note pad colour, condition, and mineral deposits. Whitish/brown crusting indicates scale buildup.

[IMAGE_PLACEHOLDER: old-pad-inspection]

  1. Step 5: Slide out old cooling pad

    2. Grasp edges firmly (rough edges possible). Slide out toward you. If stuck, gently wiggle as you pull.

[IMAGE_PLACEHOLDER: old-pad-removal]

  1. Step 6: Measure pad dimensions

    2. Note height, width, and thickness (usually 50mm or 75mm). Check manual for exact specifications.

[IMAGE_PLACEHOLDER: pad-measurement]

  1. Step 7: Obtain replacement pad

    2. Purchase replacement pad matching dimensions and type (rigid foam or cellulose). Cost $30-80 depending on type.

[IMAGE_PLACEHOLDER: replacement-pad-purchase]

  1. Step 8: Cut pad to size (if needed)

    2. If replacement is oversize, use utility knife to carefully trim to fit. Mark water inlet edge before cutting.

[IMAGE_PLACEHOLDER: pad-cutting]

  1. Step 9: Install new cooling pad

    2. Slide new pad into position, ensuring water inlet edge faces the water distribution tube. Pad should sit flush.

[IMAGE_PLACEHOLDER: new-pad-installation]

  1. Step 10: Reassemble and test

    2. Replace access panel. Turn cooler on. Check for proper water distribution across pad face. Listen for abnormal noise.

[IMAGE_PLACEHOLDER: cooler-reassembly-test]

Troubleshooting

When to Call a Professional

Professional pad replacement ($150-250) is worth considering if cooler is roof-mounted at height, if water distribution seems problematic, or if you’re uncomfortable with ladder work. our HVAC specialist can handle cooling system maintenance and diagnostics.

Tips & Gotchas

  • Replace pads in March–April, before October–February peak cooling season.
  • Use the correct pad type for your cooler—mixing types can reduce efficiency.
    • Pro tip: clean the water pump strainer filter annually to prevent mineral blockages.
  • Keep old pads for reference—they help you identify correct size and water inlet orientation.

Gotchas to Watch For:

Safety warning: turn off power completely before opening cooler—fans are powerful and can cause injury.
  • Don’t use soap or harsh chemicals to clean pads—it reduces water absorption and cooling ability.
  • Avoid oversizing pads. Tight fit is essential for water distribution. Oversized pads reduce airflow.
  • Never operate cooler without a pad installed—it damages the water pump and reduces cooling effectiveness.

Frequently Asked Questions

What’s the lifespan of an evaporative cooler pad?

Typically 12-18 months of active use. Melbourne’s dusty summers reduce lifespan. Annual replacement is recommended.

Can I reuse an old pad after cleaning?

Possibly, if lightly soiled. Heavily scaled or mouldy pads should be replaced—cleaning won’t restore efficiency.

What’s the difference between cellulose and foam pads?

Cellulose: cheaper ($30-50), good cooling, shorter lifespan (12 months). Foam: pricier ($50-80), lasts longer (18-24 months), durable.

Why is water pooling in the cooler?

Pump may be set too high, pad may be oversized, or drainage is blocked. Check and adjust pump flow rate first.

Local Resources in Melbourne

  • Bunnings (Southland, Frankston)—cooling pads, replacement parts, tools
  • Mitre 10 (various)—cellulose and foam cooling pads, water pumps
  • Climate control specialists (Melbourne)—specialty cooling pads, sizing advice, installation support
  • our HVAC specialist—evaporative cooler maintenance, pad replacement, efficiency diagnostics
  • Online retailers—hard-to-find pad sizes, overnight delivery options

Document Metadata

  • Title: DIY Evaporative Cooler Pad Replacement Guide
  • Category: Cooling

    • 🔧 Handyperson

  • Estimated Search Volume: 380/month searches/month
  • Content Type: How-to Guide
  • Target Audience: Melbourne homeowners
  • Last Updated: 2026-03-19
  • Primary Location: South East Melbourne

FAQ Schema (JSON-LD)

{

“@context”: “https://schema.org”,

“@type”: “FAQPage”,

“mainEntity”: [

{“@type”: “Question”, “name”: “…”, “acceptedAnswer”: {“@type”: “Answer”, “text”: “…”}}

]

}

Problem Solution
New pad not cooling as expected Pad may not be fully seated. Remove and reinstall, ensuring it’s flush. Check water distribution tube isn’t blocked.
Water not flowing to new pad Water inlet tube may be kinked or blocked by old pad debris. Flush tube with hose, ensure tube is straight.
Pad making noise when cooler runs Pad may not be seated properly, or motor vibration is excessive. Ensure cooler is level—use spirit level to adjust mounting.
Pad is saturating (water pooling) Water pump may be set too high. Check pump flow rate setting. Or pad is oversized—trim to fit properly.